Complement your JETvarnish 3D with Inline Embossing and Hot Foil Stamping
This new digital process completely eliminates the need for plates or
dies, as everything is controlled by a rip using digital files making
the setup time only a few minutes long. As it is using a fully digital
process, this also allows for the variable data production of embossed
and hot foil stamped effects, with each sheet being different from the
previous, with no impact on productivity. For the digital hot foil
stamping, the iFOIL solution uses market available films, allowing for a
very wide range of colors and effects, including metallic and
holographic films.
For digital embossing, the iFOIL solution in line with the JETvarnish 3D
can create a build thickness of up to 200 microns* without generating
any embossing marks on the back of the sheet. Both Embossing and Hot
Foil Stamping can be activated independently of one another or may be
combined.
iFOIL can handle all sheet formats A4 up to 52 x 105cm (Letter Size up to 20 x 40inches) and can produce at rates of up to several thousand sheets per hour. This equipment operates in line with the JETvarnish 3d digital coater.
MGI iFOIL - 20,000 Digitally Finished Covers Produced for Emballages Magazine
Untitled Document
Production Speed |
Up to 1700(1) B2 sheet size per hour (or 25m/min). |
Formats |
Min: 21 x 30 cm / 8 x 11.8" |
Max: 52 x 105 cm / 20 x 42" |
Substrate Thickness |
Min: 150 gsm and not less than 150 microns/6 mil
before printing & lamination |
Max: 600 gsm and not less than 700 microns/24 mil
before printing & lamination |
Substrates |
Foil finishing on most(2) matte or glossy laminated surfaces,
with ou without aqueous coating, layered paper, plastic, PVC and other coated materials. |
Films |
Using most(2) of the hot and cold foil. Optimization system of the film consumption. |
Roll |
Roll Size: 30 cm in max. diameter and approx. 2000 meters of film |
Min. width of 10 cm |
Up to 3 film rolls simultaneously |
Hot Foil Stamping |
On a size 52 x 74 cm, hot foil stamping surface can not exceed
51.5 x 68 cm. |
Embossing |
From 6 up to 200(3) microns in thickness. |
The surface of the metallized film may be covered with a layer
of varnish. |
Compatibility |
Online module that connects to all JETvarnish 3D. |
Electrical Requirements |
30 kW (32A) at 400 volts - 1 plug CEE/IP44 32A (3P + N +E) |
Open the doors to digital embossing and hot foil stamping with your JETvarnish 3D and iFOIL solution. Through a revolutionary digital process, the iFOIL eliminates the need for films, dies and make-ready, allowing you to produce hot foil stamping and embossing jobs from one to thousands of sheets with both very high profitability and ease of use.
From magazine covers, books, brochures, labels, to invitations and packaging, offer new services and exceptional benefits to your customers.
Exploiting both visual and tactile excitement that the JETvarnish 3D and iFOIL brings, not only will you now be able to finally bring Hot Foil Stamping in house, but you will be able to do it with virtually no set up and high speeds but also the possibility to offer a new never before seen finish; the personalization of embossed hot foil.
Easy to use, iFOIL works in-line with the JETvarnish 3D digital spot UV coater. A software suite allows you to easily understand and modify layouts, with sizes ranging from A4 format to 52 x 105 cm and on paper substrates ranging from 150 to 700 microns.
It is possible to make hot stamping with iFOIL from printing done on offset and digital presses including the METEOR Digital Press Series.
|